How To Set Up A Coleman Saluspa
#90363
110-120V~60Hz, 12A at 20ºC (68°F)
Owner'southward Manual
Website: www.bestwaycorp.com/back up
DO Non Render THIS ITEM TO THE Store OR WEBSITE WHERE Information technology WAS PURCHASED. PLEASE VISIT WWW.BESTWAYCORP.COM/SUPPORT FOR QUESTIONS, OR FOR DEFECTIVE OR WARRANTY CLAIMS.
Alert
IMPORTANT Prophylactic INSTRUCTIONS
When using this electrical equipment, basic prophylactic precautions should e'er be followed, including the post-obit:
READ AND FOLLOW ALL INSTRUCTIONS.
WARNING – To reduce the adventure of injury, do not permit children to use this production unless they are closely supervised at all times. A wire connector is provided on this unit of measurement to connect a minimum of 6 AWG (13.3 mm2) solid copper conductors between this unit and whatsoever metal equipment, metal enclosures of electrical equipment, metal h2o
piping, or conduit within 5 feet (1.five m) of the unit of measurement.
DANGER – Risk of injury.
a) Supercede the damaged string immediately.
b) Exercise not bury the string.
c) Connect to a grounded, grounding-blazon receptacle simply.
WARNING – This production is provided with a basis-fault circuit interrupter integrated with the power plug at the end of the cord. The GFCI must be tested before each apply. With the product operating, push the test button on the GFCI and the product should not operate. Push the reset button on the GFCI and the product should now operate ordinarily. When the product fails to operate in this way, at that place is a basis current flowing indicating the possibility of an electric shock. Disconnect the power until the fault has been identified and corrected.
DANGER – Risk of Accidental Drowning. Extreme circumspection must be exercised to preclude unauthorized access past children. To avoid accidents, ensure that children cannot utilise this spa unless they are supervised at all times.
DANGER – Gamble of Injury. The suction fittings in this spa are sized to match the specific water flow created by the pump. Should the need ascend to replace the suction fittings or the pump, exist sure that the flow rates are compatible? Never operate spa if the suction fittings are broken or missing. Never replace a suction fitting with 1 rated less than the period rate marked on the original suction fitting.
DANGER – Risk of Electric Shock. Install at least v anxiety (i.5 k) from all metal surfaces. Equally an alternative, a spa may be installed within 5 anxiety of metal surfaces if each metal surface is permanently connected by a minimum of vi AWG (13.3 mm 2) solid copper conductors to the wire connector on the terminal box that is provided for this purpose.
DANGER – Hazard of Electric Shock. Do not permit any electric apparatus, such equally a light, telephone, radio, or television set, inside v feet (1.5 m) of a spa.
WARNING – To reduce the risk of injury:
a) The water in a spa should never exceed twoscore°C (104°F). Water temperatures between 38°C (100°F) and 40°C (104°F) are considered prophylactic for a healthy adult. Lower water temperatures are recommended for young children and when spa use exceeds x minutes.
b) Since excessive water temperatures have a high potential for causing fetal damage during the early months of pregnancy, pregnant or peradventure significant women should limit spa water temperatures to 38°C (100°F).
c) Before entering a spa, the user should measure out the water temperature with an accurate thermometer since the tolerance of h2o temperature-regulating devices varies.
d) The use of booze, drugs, or medication before or during spa utilize may lead to unconsciousness with the possibility of drowning.
e) Obese persons and persons with a history of center disease, low or high blood pressure, circulatory arrangement issues, or diabetes should consult a physician earlier using a spa.
f ) Persons using medication should consult a physician earlier using a spa since some medication may induce drowsiness while other medication may affect center rate, blood pressure level, and circulation.
Alarm: TO AVOID ELECTRIC SHOCK, Do Not Utilize THE SPA WHEN Information technology IS RAINING.
Warning: Water attracts children; Always adhere a spa cover subsequently each use.
Alert: TO REDUCE THE Run a risk OF INJURY: Never add water that is college than 40°C (104°F) into the Spa. CONSULT YOUR PHYSICIAN FOR RECOMMENDATIONS.
Circumspection: The spa should non be set up or left out in temperatures lower than four°C (forty°F).
CAUTION: Exercise not use the spa solitary.
CAUTION: Ever enter and go out the spa slowly and charily. Wet surfaces are glace.
Caution: To avoid damage to the pump, the spa must never be operated unless the spa is filled with water.
Caution: Immediately leave spa if the user feels uncomfortable or sleepy.
Annotation: Delight examine equipment before use. Notify Coleman at the customer service accost listed on this manual for whatever damaged or missing parts at the fourth dimension of buy. Verify that the equipment components correspond the model that you had intended to purchase.
SAVE THESE INSTRUCTIONS
WARNING: CHILDREN SHOULD NOT USE SPAS OR HOT TUBS WITHOUT Adult SUPERVISION.
Warning: Exercise NOT USE SPAS OR HOT TUBS UNLESS ALL SUCTION GUARDS ARE INSTALLED TO PREVENT Body AND HAIR ENTRAPMENT.
WARNING: PEOPLE USING MEDICATIONS AND/OR HAVING AN ADVERSE MEDICAL HISTORY SHOULD CONSULT A PHYSICIAN Before USING A SPA OR HOT TUB.
Alarm: PEOPLE WITH INFECTIOUS DISEASES SHOULD NOT Employ A SPA OR HOT TUB.
Alert: TO Avoid INJURY, EXERCISE CARE WHEN Inbound OR EXITING THE SPA OR HOT TUB.
WARNING: Practice NOT USE DRUGS OR ALCOHOL Before OR DURING THE USE OF A SPA OR HOT TUB TO Avert UNCONSCIOUSNESS AND POSSIBLE DROWNING.
Alarm: PREGNANT OR POSSIBLY PREGNANT WOMEN SHOULD CONSULT A PHYSICIAN BEFORE USING A SPA OR HOT TUB.
WARNING: WATER TEMPERATURE IN EXCESS OF 38°C (100°F) CAN Exist INJURIOUS TO YOUR Wellness.
WARNING: Earlier ENTERING THE SPA OR HOT TUB, Measure THE Water TEMPERATURE WITH AN Authentic THERMOMETER.
Alert: DO Non USE A SPA OR HOT TUB IMMEDIATELY FOLLOWING STRENUOUS Practice.
WARNING: PROLONGED IMMERSION IN A SPA OR HOT TUB CAN Exist INJURIOUS TO YOUR Wellness.
Warning: Exercise NOT PERMIT ELECTRIC APPLIANCES (SUCH AS A Light, Phone, RADIO, OR Goggle box) WITHIN 1.5 1000 OF THIS OR HOT TUB.
Caution: MAINTAIN H2o CHEMISTRY IN ACCORDANCE WITH THE MANUFACTURER'S INSTRUCTIONS.
ASSEMBLY: THE PROVIDED WARNING Label
WARNING
REDUCE THE Take a chance OF ELECTROCUTION
- NEVER Place AN Electrical APPLIANCE Within five Anxiety OF SPA.
REDUCE THE RISK OF CHILD DROWNING
- SUPERVISE CHILDREN AT ALL TIMES.
- Adhere SPA COVER AFTER EACH USE.
REDUCE THE Adventure OF OVERHEATING
- CHECK WITH A DOCTOR Before USE IF Pregnant, DIABETIC, IN POOR HEALTH, OR Under MEDICAL CARE.
- Leave IMMEDIATELY IF UNCOMFORTABLE, DIZZY, OR SLEEPY. SPA HEAT CAN CAUSE HYPERTHERMIA AND UNCONSCIOUSNESS.
- SPA HEAT IN CONJUNCTION WITH ALCOHOL, DRUGS, OR MEDICATION CAN CAUSE UNCONSCIOUSNESS.
WHEN PREGNANT, SOAKING IN HOT Water FOR LONG PERIODS Tin Impairment YOUR FETUS. MEASURE WATER TEMPERATURE Earlier ENTERING.
- Exercise NOT ENTER SPA IF WATER IS HOTTER THAN 38ºC (100ºF)
- DO Non STAY IN SPA FOR LONGER THAN 10 MINUTES.
NOTE: The alert label must be posted near your spa in a readable position during using your spa.
- Take out the warning characterization from the accessory kit.
- Carefully peel the alarm label.
- Affix the alarm label.
To gild the warning label, please contact your local Coleman After Sales Service.
IMPORTANT!
To accomplish 40ºC (104ºF), the heating duration required is based on the starting water temperature and ambient temperature. The data below is purely for reference. To display the current water temperature, run the filter system for at least a minute.
| Ambient Temperature | H2o Temperature | Set Temperature | Heating Duration | |||
| x°C | (l°F) | ten°C | (fifty°F) | 40°C | (104°F) | 32h |
| 15°C | (59°F) | 15°C | (59°F) | 40°C | (104°F) | 26h |
| 20°C | (68°F) | xx°C | (68°F) | 40°C | (104°F) | 20h |
| 25°C | (77°F) | 25°C | (77°F) | forty°C | (104°F) | 14h |
| 30°C | (86°F) | 30°C | (86°F) | 40°C | (104°F) | 9h |
Be sure to cover the spa with the spa embrace whenever the heating function is activated. Leaving the spa uncovered will increase the heating elapsing required. Please exercise non use the spa when the ambient temperature is lower than 4ºC (39°F ).
Salve THESE INSTRUCTIONS
SPECIFICATIONS
| Capacity: | iv-6 Adults | Massaging Turbo Blower: | 6.5A | Increased Heat Rate: | Approximately two-3°F/h (one-1.five°C/h) |
| Water Chapters (80%): | 242 gal. (916 L) | Oestrus Element: | 11.3A at 68°F (20°C) | Ability Rate: | 110-120V AC, 12A at 68°F (20°C) |
| Inflated Size: | 77in. 10 28in. (i.96m x 71cm) | Pump: | 0.7A Circulation Filter Pump | Working Pressure level: | 0.08Bar (1.2PSI) |
| Filled Weight: | ii,103 lbs. (954 kg) | Temperature Capacities: | 104°F (40°C) | Actual Water Menstruation: | 320 gal./h (1,211 Uh) |
NOTE: The to a higher place heating rate is based on a lab examination conducted with an ambience temperature of 25ºC (77ºF) and above.
| Role North. | Office Code | Description | QTY |
| 001 | 90363TASS19 | Pool liner | 1 |
| 002 | P4G080ASS18 | Spa Heater | 1 |
| 003 | P5G400ASS19 | Elevation Leatheroid Cover | one |
| 004 | 90363GASS17 | Inflatable Cover | 1 |
| 005 | P6930018 | Aggrandizement Hose | 1 |
| 006 | P6653 | Filter Set | two |
| 007 | P61960 | Chemic Dispenser | one |
| 008 | 58321(H)S15 | Ground Mat | ane |
| 009 | F6H189 | Wrench | i |
| 010 | P6575 | Stoppers | 3 |
| 011 | P6611 | Cover Adapter A | 1 |
| 012 | P6H971 | Aggrandizement Valve | 1 |
| 013 | F6414 | Buckle | 6 |
| 014 | 90352E | Filter Catridge | 2 |
| 015 | P61726 | Deflation T-joint | one |
| 016 | P61725 | Deflation Valve Adapter | 1 |
| 017 | F6H1085 | Spa Droppings Screen | ane |
INSTALLATION
Selected Location
Of import: Because of the combined weight of the SaluSpa, water, and users, information technology is extremely of import that the base where the SaluSpa is installed is smoothen, flat, level, and
capable of uniformly supporting the weight for the entire time the SaluSpa is installed ( non on the carpet or other similar material). If the SaluSpa is placed on a surface, which does non meet these requirements, whatsoever damage caused past improper support is not covered nether the manufacturer's warranty. It is the responsibleness of the SaluSpa owner to assure the integrity of the site at all times.
- Indoor Installation:
Exist aware of special requirements if y'all install the spa indoors.
• Humidity is a natural side effect with SaluSpa installation. Determine the effects of moisture on exposed forest, paper, etc. in the proposed location. To minimize these effects, it is all-time to provide plenty of ventilation to the selected area. An architect can help decide if more ventilation is needed. - Outdoor Installation:
• During filling, draining, or when in use, water may spill out of the spa. Therefore the SaluSpa should be installed most a floor drain.
• Do not go out the spa'southward surface exposed to straight sunlight for long periods of fourth dimension.
GFCI Exam
IMPORTANT: RISK OF ELECTRIC Stupor. THE GFCI MUST Be TESTED Before TURNING ON THE PUMP EACH Fourth dimension.
- Plug the GFCI into a power outlet.
- Press the reset button, the indicator turns ruddy.
- Press the test button, the indicator turns off.
- Press the reset button again, the indicator turns ruby and the spa is set for utilise.
WARNING: The GFCI plug must exist tested before each use to avoid the risk of electrical stupor.
WARNING: Before inserting the plug into a power outlet, make certain the current charge per unit of the power outlet is suitable for the pump.
Alarm: Do not utilize the pump if this exam fails and contact our Aftersales Service.
NOTE: When inflating, you will notice that air volition exist expelled from the area where the air hose connects to the pump, this is normal for technique requirements.
NOTE: Practice non utilise an air compressor to inflate the puddle.
Notation: Practice non drag the pool on rough footing as this may cause damage to the puddle liner.
NOTE: Aggrandizement time for reference merely.
Air Valve Check
Always check the air valve carefully before inflation to ensure there is not an air leak. If the air valve is loose, utilize the provided wrench to fasten the air valve following these
steps: With one manus, concur the backside of the air valve from the inner side of the spa wall and plough the wrench clockwise.
Notation:
- Practice non overtighten.
- Do non accommodate the air valve connector when the spa is in use.
Hyperthermia occurs when the internal temperature of the trunk reaches a level several degrees above the normal trunk the temperature of 37°C (98.6°F). The symptoms of hyperthermia include an increase in the internal temperature of the body, dizziness, lethargy, drowsiness, and fainting. The effects of hyperthermia include failure to perceive rut; failure to recognize the need to go out spa or hot tub; unawareness of impending take chances; fetal impairment in pregnant women; physical inability to exit the spa or hot tub; and unconsciousness resulting in the danger of drowning.
Alert – The use of alcohol, drugs, or medication can profoundly increase the risk of fatal hyperthermia.
Alarm: Water TEMPERATURE IN EXCESS OF 38°C (100°F) Tin BE INJURIOUS TO YOUR HEALTH.
A Lock/Unlock Push
The pump has a five-minute automobile-lock. To lock or unlock the pump, place a finger over the lock/unlock push button for 3 seconds.
B Power-Saving Timer Button
This is a newly added function, designed to help avoid wasting power by setting the time and duration of the heating cycle for the spa. This fashion, yous tin enjoy your spa at the time you lot desire, without needing to leave the heater on at all times.
Step 1: Ready the heating duration
- Press the push unit the
LED starts to flash. - Press the
push to adjust the heating duration (From 1-48 hours). - Press the push again to ostend the heating elapsing.
STEP 2: Set the number of hours FROM At present when the heater will activate
- After setting the heating duration, the
LED starts to flash. - Press the button to adjust the hours until the time of activation (From 0-99 hours).
- Press the button again or merely touches cipher for ten seconds to confirm the setting. The LED will low-cal steadily, and the countdown to heater activation will
begin.
To modify the timer settings: Press the button and utilise the button to adjust.
Cancel the setting: Press the push button for 2 seconds.
Annotation: Later setting, the screen flashes the current temperature and fourth dimension alternately.
NOTE: Timer aligning (amount of time with the heater ON) may exist fix from 1 to 48 hours; Reservation fourth dimension adjustment (the number of hours FROM Now when the heater will begin to office) may be set from 0 to 99 hours. If the timer is set at 0 hours, the heating system will activate immediately. Note that the timer is a one-fourth dimension peruse – the user sets the duration of the heating bicycle, and how many hours from now the heating cycle begins. The timer does NOT repeat until reset.
C Massage System Button
Utilise this push button to actuate the massage organization, which has a 30-minute car-shutoff characteristic. The light in a higher place the massage system push displays cherry when activated.
IMPORTANT: Do non run the massage system when the embrace is attached. Air can accrue inside the spa and cause irreparable damage to the encompass and actual damage.
NOTE: Heat and massage systems work together to create a warm massage experience.
D Celsius/Fahrenheit Toggle
The temperature can be displayed in either Fahrenheit or Celsius.
E Heat Push
Apply this button to activate the heating system. When the light above the heat button is red, the heating system is activated. When the calorie-free is greenish, the h2o is at the prepare
temperature and the heating organization is at residual.
Annotation: If the heating system is activated the filtration organization will automatically beginning.
NOTE: After turning off the heating system the filtration system volition go along to operate.
F H2o Filter Push
This button turns the filter pump on and off. The calorie-free above the Water Filter Push button displays red when activated.
G Temperature Aligning Buttons
Pressing the Temperature Increment or Decrease buttons volition crusade the LED to flash. When flashing you can adjust to the desired temperature setting. If you concord these buttons downwards, the values will chop-chop increase or decrease. The new and desired temperature setting will remain on the LED display for 3 seconds to ostend the new value.
Note: The default temperature is 35°C (95°F).
NOTE: Temperature adjustment ranges from 20°C (68°F) to xl°C (104°F).
H On/Off Button
Press this button for 2 seconds to activate the control panel buttons and the light turns green. Printing this button for 2 seconds to turn off all currently activated functions.
I Power-Saving Timer LED
This LED flashing means you are setting the heating duration. The lite volition be on when the heating function starts to piece of work.
This LED flashing means you are setting the number of hours FROM NOW when the heater will activate. When the light is on, the Ability-Saving Timer part is set.
J LED Display
Once powered up the LED displays the current water temperature automatically.
After 72 hours of filtration (without using the ability saving timer role), the pump volition hibernate and flash "End" with the current water temperature. When the pump is hibernating both the heating and h2o filter functions are disabled. To re-actuate the pump press the lock/unlock button for three seconds.
Annotation: The water rut rate may change in the conditions below:
- When the outdoor temperature is below fifteen°C (59°F).
- If the cover is non in position when the heating function is activated.
Notation: To display the current water temperature, run the filter system for at least a minute. The water temperature as tested by an external thermometer may vary from the
temperature as displayed on the spa panel by as much as approximately 2°C.
Alarms
| Causes | Reasons | Solutions | |
 | The h2o menstruation sensors work without pressing the filter or heat push. |
|
|
 | Subsequently starting or during the functions of filtering or/and heating, the water catamenia sensors exercise not find h2o flow. |
|
|
 | The pump's thermometer reads the water temperature below 4°C (40°F). |
|
|
 | The pump's thermometer reads the water temperature over 48°C (119°F). |
|
|
 | The pump'due south thermometer connections have issues. |
| Contact your local Coleman After Sales Service point to get instructions. |
 | The thermal cut-out cut-off. |
|
|
Maintenance
NOTE: Your spa will require additional air to exist added from time to time. Changes in temperature from day to night will alter the pressure in the spa and may cause a sure corporeality of deflation. Please follow the Assembly instructions and drain the spa before inflating to the accurate pressure level needed.
Circumspection: YOU MUST ENSURE THE PUMP IS UNPLUGGED Before BEGINNING SPA MAINTENANCE TO AVOID THE RISK OF INJURY OR Expiry.
Filter Cartridge Maintenance
NOTE: To ensure your spa water stays clean, check and clean your filter cartridges every mean solar day follow the steps beneath.
Note: We recommend changing your filter cartridges every week or, if the filter cartridges remain soiled and discolored, they should be replaced.
Water Maintenance
Keeping your spa water clean and chemically balanced is necessary. Simply cleaning the filter cartridge is not enough for proper maintenance, we recommend yous use pool chemicals to maintain water chemical science and chlorine or bromine tablets (practice not employ granules) with the chemical dispenser.
Note: We recommend you lot take a shower before using your SaluSpa, equally cosmetic products, lotions, and other residues on the skin tin quickly dethrone
water quality.
To use the chemical dispenser, please follow the below instruction.
Using chemical tablets (non included):
Annotation: Remove the chemical dispenser from spa when the spa is in use.
IMPORTANT: Later performing chemical maintenance and before using the spa, use a test kit (not included) to exam the water chemistry. Nosotros recommend maintaining your
water as below table.
| pH | Full Alkalinity | Free Chlorine |
| 7.4-seven.vi | 80-120ppm | 2-4ppm |
NOTE: Damage resulting from chemic imbalance is not covered by the warranty. Pool chemicals are potentially toxic and should be handled with care. At that place are serious health risks from chemical vapors and the incorrect labeling and storage of chemic containers. Please consult your local pool supply retailer for more information about chemical maintenance. Pay close attention to the chemic manufacturer'southward instructions. Spa damage resulting from the misuse of chemicals and mismanagement of spa water is not covered by the warranty.
Draining the Spa
Note: Drawings for illustration purposes simply. May not reverberate the actual product. Not to scale.
Cleaning the spa
Detergent residues and dissolved solids from bathing suits and chemicals may build up on the spa walls. Use soap and water to clean the walls and rinse thoroughly.
Notation: DO Not apply hard brushes or abrasive cleaners.
DEFLATION
Spa Repair
For inflatable cover.
If the spa is torn or punctured, utilize the provided heavy-duty repair patch.
- Clean expanse to exist repaired.
- Carefully skin patch.
- Press patch over the area to exist repaired.
- Wait thirty seconds before aggrandizement.
For Spa liner.
If the spa is torn or punctured, utilize the provided PVC repair patch and glue (not included) following these steps:
- Clean and dry out area to be repaired.
- Cut the provided PVC patch to the appropriate size.
- Use glue (not included) to coat 1 side of the newly cut patch. Brand sure the glue is evenly distributed.
- Expect for 30 seconds and then place the cut patch with glue over the damaged surface area.
- Smooth out whatever bubble of air that may be trapped underneath, and press firmly for 2 minutes.
- The product is once once more prepare for use. Echo this process should further leaks occur.
- Wait 30 minutes before aggrandizement.
Spa Storage
Make certain the spa and pump are completely dry. This is essential to extend the life of the spa. It is recommended you lot store the spa in its original bundle in a warm dry place.
NOTE: Plastic becomes brittle and susceptible to breaking when exposed to subzero temperatures. Freezing can severely impairment the spa. Improper winterization of the spa can void your warranty.
TROUBLESHOOTING
Bestway strives to provide the almost problem-gratis Spas on the market. If you experience whatsoever problems whatsoever, do not hesitate to contact Bestway or your authorized dealer. Hither are some helpful tips to help you lot to diagnose and rectify some common sources of problem.
| Problems | Probable Causes | Solutions |
| Pump does not operate | – Power failure – GFCI cleaved | – Check power source – Contact your local Bestway After-Sales service bespeak to get instructions |
| Pump does not heat properly | – Temperature set too low – Muddy Filter Cartridge – The thermal cutting-out cut off – Spa is not covered – Heating element failed or fuse cutout | – Set to a college temperature refer to department pump functioning – Make clean/replace the filter cartridge refer to department filter cartridge cleaning and replacement – Unplug the pump, and put the plugin in a dry, cool place. Only restart the pump when the water temperature reaches 35°C (95°F) or lower – Attach the encompass. – Contact your local Bestway After-Sales service point to get instructions |
| Massage Arrangement does non piece of work | – Air Pump is overheating – The massage system stops automatically – Air pump is broken | – Unplug the pump and wait two hours until the pump has cooled. Insert the plug and printing the massage system push button – Press the massage system push button to reactivate – Contact your local Bestway Aftersales Service Center for instructions |
| Pump adapters are not level with the spa adapters | – I characteristic of PVC is that information technology changes shape, which is normal | – Elevate the pump with wood or another type of insulating material to bring the pump's adapters level with the spa'due south adapters |
| Spa pool leakage | – Spa is torn or punctured – Air valve is loose | – Use provided repair patch – Using soapy water, cover the air valve to check if the air is leaking, if so, use the provided wrench to spike the air valve following these steps:
|
| Water is non clean | – Bereft filtering time – Dirty Filter Cartridge – Improper water maintenance | – Increment filtration time – Clean/supervene upon the Filter Cartridge (refer to Filter Cartridge Cleaning and Replacement section) – Refer to the chemic manufacturer's instructions |
| Control console not working | – The control panel has an auto-lock, which is activated subsequently 5 minutes of inactivity. The LED brandish has ane icon: If the lock icon is highlighted, the control panel is locked.– Command panel is not activated. | – To unlock the command panel, printing the  button for 3 seconds. If the control console volition not unlock, restart the pump – unplug and plug in the pump.– Press the on/off push button for 2 seconds. If the problem persists, delight contact your local Bestway Aftersales Service Center for instructions. |
| GFCI test failed | There is a defect in your spa | Contact your local Bestway Aftersales Service Center and return the SPA. |
| What kind of chemicals should be used for h2o maintenance? | Please consult your local chemical supplier for information about chemical maintenance. Pay close attention to the chemic manufacturer's instructions. | |
| Water leaks from the adapters between the pump and spa | Insert the three stopper caps onto the spa's ports to prevent water from escaping and disconnect the pump. Bank check and make sure the seals are placed correctly within the pump adapters. If the seals are missing or not installed correctly, delight contact your local Bestway Aftersales Service Middle for instructions. If the seals are correctly in place, reconnect the pump to the spa and hand-tighten the adapters. | |
The product you accept purchased comes accompanied by a limited warranty. Bestway® stands behind our quality guarantee and assures, through a replacement warranty, your product will be gratuitous from manufacturer's defects. The express warranty is valid equally follows: 360 days for the heater pump from the original date of purchase 180 days for the pool liner from the original date of purchase xxx days for hoses, fittings, and accessories included in the parcel from the original date of purchase To enact a warranty claim, delight contact your local Bestway® Later Sales Eye at i-855-838-3888 before sending whatever documents. They volition provide total instructions on what is needed for your claim. Bestway® is not responsible for economic loss due to h2o or chemical costs. Bestway® volition not replace any products deemed to have been neglected or used outside of the owner's transmission guidelines. Bestway's warranty covers manufacturing defects discovered while unpacking the production or during use equally recommended within the user manual. This warranty applies only to products that have non been modified past any 3rd parties. The product must be stored and handled in accordance with the technical recommendations.
The warranty does not cover damages caused by misuse, abuse, neglect, including, but non limited to standoff, fire, apply of wrong voltage, excessive estrus exposure, improper installation, improper wiring or testing, or improper storage. Replacements and repairs don't extend the elapsing of the warranty. The Limited Warranty is valid for the flow indicated in a higher place. The warranty showtime engagement is the date of sale shown on the original receipt/purchase invoice.
Please choose your Spa
TO: Bestwar Service Department Appointment of purchase' _______________________
Date: ________________________________________ Customer Code Number__________________
Website: www.bestwaycorp.com Toll-Free: 1-855-838-3888 Please provide your address details in full.
Notation: Incomplete address details will result in delayed shipments.
Bestway) reserves the right to charge for re-commitment of undelivered packages where the recipient is at fault.
REQUIRED Data – Please WRITE THE Aircraft ADDRESS
Proper noun:_____________________________________________________ Address:_______________________
City: ______________________________________________________ State / Country_________________
Cipher Code: ______________________________________ Retailer:_______________________
Mobile: ____________________________________________________ Telephone:_____________________
Fax:_______________________________________________________ Electronic mail: _______________________
Spa Pump Batch Number:_____________________________ Spa Pool Batch Number:________
Spa Pump Particular Code:
All drawings for illustration purpose merely. Not to scale.
Problem clarification
 Spa leakage | Water Filtration System not working | Heating System not working |
| Control panel shows a failure that cannot exist solved | Massage Organisation not working | |
| Pump leakage | Adapter leakage |  Missing Part – Please use the lawmaking for the missing part. This can be establish in the owner's manual. |
| Other (Delight depict) | ||
IMPORTANT: Simply THE DAMAGED Part WILL BE REPLACED, NOT THE COMPLETE Prepare.
Bestway® reserves the right to request photographic testify of defective parts, or to crave sending the particular for additional testing. In order to better assistance you, we request all information you provide to be complete.
FOR FAQ, MANUALS, VIDEOS, OR SPARE PARTS, PLEASE VISIT OUR WEBSITE: world wide web.bestwaycorp.com.
303021185672
Documents / Resources
Source: https://manuals.plus/coleman/90363-saluspa-inflatable-hot-tub-manual
0 Response to "How To Set Up A Coleman Saluspa"
Post a Comment